Phone 877-210-6361 1SIGN UP 2REVIEW DESIGNS 3APPROVE QUOTE
All Doors
All Doors

Individual Cabinet Assembly Instructions

Cream Maple

Recommended Tools:
Flathead / Philips Screwdriver
Required Tool
Electric Screwdriver
Recommended Tool
Rubber Head Hummer
Recommended Tool
3/4" Staples Gun
Recommended Tool
Hot Glue Gun
Recommended Tool

Base Cabinet

STEP 1:

Remove the door from the frame.  It is best to re-install the door after the installation of all the cabinets. Otherwise, doors might be damaged during the assembly and installation of the cabinet boxes.

Kitchen Cabinets - Assembly Picture
STEP 2:

Locate the two top, interior support pieces.

Kitchen Cabinets - Assembly Picture
STEP 3:

Secure the side panel to the frame using 1/4" wide by 3/4" deep staples every 6".

Kitchen Cabinets - Assembly Picture
STEP 4:

If you are using hot glue (optional, but recommended) make sure to apply a thin layer of glue over the connection of the side panel and the frame (from the inside of the cabinet as shown in the photo).

Kitchen Cabinets - Assembly Picture
STEP 5:

Repeat Steps 3 and 4 with the other side panel.

Kitchen Cabinets - Assembly Picture
STEP 6:

Insert the bottom panel through the grooves.  Staple every 4-6'' and apply hot glue.

Kitchen Cabinets - Assembly Picture
STEP 7:

Slide in the back panel starting from the bottom moving toward the top.

Kitchen Cabinets - Assembly Picture
STEP 8:

Make sure both panels are aligned. Otherwise, it will be very difficult to level the plywood for the countertop.

Kitchen Cabinets - Assembly Picture
STEP 9:

Staple the bottom of the back panel to secure it to the frame (use 3/4'' staples every 4-6'').

Kitchen Cabinets - Assembly Picture
STEP 10:

Staple the side panel to the cabinet for extra reinforcement. Use either 3/4'' or 1'' staples.  Use two staples on each side of the cabinet.

Kitchen Cabinets - Assembly Picture
STEP 11:

Locate the toe kick plate.

Kitchen Cabinets - Assembly Picture
STEP 12:

Staple it to the bottom of the cabinet using 3/4'' staples every 4-6''.

Kitchen Cabinets - Assembly Picture
STEP 13:

Congratulations! Your cabinet is now ready. Please see the drawer assembly instructions for further assistance.

Kitchen Cabinets - Assembly Picture
STEP 14:

Locate all of the following parts:

1. Bottom panel

2. Two side panels (long ones)

3. Back panel

4. Front panel (drawer face)

Kitchen Cabinets - Assembly Picture
STEP 15:

Connect the side panel to front panel.

Optional: Use carpenter's glue to glue connections.

Kitchen Cabinets - Assembly Picture
STEP 16:

Connect the other side panel.

Kitchen Cabinets - Assembly Picture
STEP 17:

Slide in the bottom panel to the groove on the bottom.

Kitchen Cabinets - Assembly Picture
STEP 18:

Make sure bottom panel is aligned with the back of the side panels.

Kitchen Cabinets - Assembly Picture
STEP 19:

Connect the back panel. Make sure that the notch and the pre-drilled holes are facing down.

Kitchen Cabinets - Assembly Picture
STEP 20:

Locate the pre-drilled holes on the side of the cabinet.

Connect the drawer guides using a drill or a screwdriver.

Kitchen Cabinets - Assembly Picture
STEP 21:

Make sure the front of the drawer guides align with the back side of the face frame.



In the photo the left guide is installed correctly. The right one is NOT CORRECT because the front of the guide passes the back side of the face frame.

Kitchen Cabinets - Assembly Picture
STEP 22:

Slide drawer until the pins are in the holes.

Kitchen Cabinets - Assembly Picture
STEP 23:

Insert the pins in the holes.

Note: The round plate under the pin can be used for easy adjustments.

Congratulations! Your drawer is now ready.

Kitchen Cabinets - Assembly Picture

Base Diagonal Corner

STEP 1:

Locate the face frame and the front door.

Kitchen Cabinets - Assembly Picture
STEP 2:

Remove the door from the frame.

Kitchen Cabinets - Assembly Picture
STEP 3:

- Locate the bottom shelf the the Black rotating hinge.

- Connect the Black spinning hinge to the bottom shelf using four screws.

- Make sure the grove of the bottom shelf (at the bottom of this photo) will face up.

Kitchen Cabinets - Assembly Picture
STEP 4:

Locate the bottom spinning tray (the one with the three pre-drilled holes on the bottom (the top spinning tray has four pre-drilled holes).

Kitchen Cabinets - Assembly Picture
STEP 5:

Connect the bottom shelf to the spinning tray using three screw from the back (the bottom) of the bottom shelf.

Kitchen Cabinets - Assembly Picture
STEP 6:

Close up on the back (bottom) of the bottom shelf.

Kitchen Cabinets - Assembly Picture
STEP 7:

This is how the spinning tray should look like when connected to the bottom shelf.

Kitchen Cabinets - Assembly Picture
STEP 8:

Connect the face frame to the front site panel using two of the supplied angled brackets.

Kitchen Cabinets - Assembly Picture
STEP 9:

Connect the other front side panel using two additional angled brackets.

Kitchen Cabinets - Assembly Picture
STEP 10:

Insert the bottom shelf with the spinning tray in the pre-drilled slots on the front side panels and the face frame.

Kitchen Cabinets - Assembly Picture
STEP 11:

Connect the back side panel to the front side panel using the supplied 90 degrees bracket.

Kitchen Cabinets - Assembly Picture
STEP 12:

Secure the back side panel to the bottom shelf using three screws in the pre-drilled holes. Do not secure the screw all the way in this point to allow some flexibility until all the panels will be connected properly.

Kitchen Cabinets - Assembly Picture
STEP 13:

Repeat the last two steps with the other side.

Kitchen Cabinets - Assembly Picture
STEP 14:

Slide in the back panel in the pre-drilled slots.

Kitchen Cabinets - Assembly Picture
STEP 15:

Connect the top support piece using three screws to the back panel and 2 screws on each side to the back side panels.

Kitchen Cabinets - Assembly Picture
STEP 16:

Locate the top spinning tray, the top Black spinning hinge and the top shelf.

Kitchen Cabinets - Assembly Picture
STEP 17:

Connect the top black spinning hinge to the top shelf using four screws. Make sure the pre-drilled holes on the top shelf are facing up.

Kitchen Cabinets - Assembly Picture
STEP 18:

Connect the top black spinning hinge to the back of the top spinning tray using four screws in the pre-drilled holes.

Kitchen Cabinets - Assembly Picture
STEP 19:

Place the top shelf with the spinning tray on top of the two support blocks on the back side panels. Secure using two screws on each side.

Kitchen Cabinets - Assembly Picture
STEP 20:

Connect the toe-kick piece on the bottom of the cabinet using two screws on each side.

Kitchen Cabinets - Assembly Picture
STEP 21:

Connect the door to the face frame.

Your cabinet is now ready!

Kitchen Cabinets - Assembly Picture

Base End

STEP 1:

Locate the two face frames and doors.

Kitchen Cabinets - Assembly Picture
STEP 2:

Remove both doors from the frame. Do NOT remove the drawers face and they are decorative (fake).

Kitchen Cabinets - Assembly Picture
STEP 3:

Connect the two face frame together using the supplied 3 angled brackets.

Kitchen Cabinets - Assembly Picture
STEP 4:

Insert the bottom panel in the slots.

Kitchen Cabinets - Assembly Picture
STEP 5:

Connect the side panel to the back panel. Secure the panels using staples between the side panel the and bottom panel.

Kitchen Cabinets - Assembly Picture
STEP 6:

Repeat the previous step with the other side panel.

Kitchen Cabinets - Assembly Picture
STEP 7:

Slide in the back panel.

Kitchen Cabinets - Assembly Picture
STEP 8:

Reinforce the cabinet structure using staples every 6'' between the side panels and the back panel.

Kitchen Cabinets - Assembly Picture
STEP 9:

Locate the two toe-kick pieces and join them together using staples as shown in the photo.

Kitchen Cabinets - Assembly Picture
STEP 10:

Secure the toe-kick using staples (two in each side).

Kitchen Cabinets - Assembly Picture
STEP 11:

Re-connect the two front doors and install the shelf.

Your cabinet in now ready!

Kitchen Cabinets - Assembly Picture

Base Lazy Susan

STEP 1:

Locate both parts of the face frame.

Kitchen Cabinets - Assembly Picture
STEP 2:

Connect both face frame parts as shown in the photo.

Kitchen Cabinets - Assembly Picture
STEP 3:

Secure parts by using two screws in each connection (four screws in total).

Kitchen Cabinets - Assembly Picture
STEP 4:

This is how it should look once you've finished Step 3.

Kitchen Cabinets - Assembly Picture
STEP 5:

Flip the built frame so the long, unattached part faces up.

Kitchen Cabinets - Assembly Picture
STEP 6:

Insert the side of the cabinet into the grooves. Make sure the finished side is facing outwards like in the photo.

Kitchen Cabinets - Assembly Picture
STEP 7:

Here is a side view.

Kitchen Cabinets - Assembly Picture
STEP 8:

Staple the side to the frame using 3/4'' staples every 4 to 6".

Kitchen Cabinets - Assembly Picture
STEP 9:

For more durability, apply a layer of hot glue on the connection between the face frame and the cabinet side.

Kitchen Cabinets - Assembly Picture
STEP 10:

Insert the second side panel into the grooves.

Kitchen Cabinets - Assembly Picture
STEP 11:

Staple the second side panel to the frame every 4 to 6'' using 3/4'' staples.


If you are also using hot glue, apply a thin layer on connections.

Kitchen Cabinets - Assembly Picture
STEP 12:

Locate the bottom panel.

Kitchen Cabinets - Assembly Picture
STEP 13:

Insert the bottom panel to the grooves.

Kitchen Cabinets - Assembly Picture
STEP 14:

Staple the bottom panel to the frame. Apply hot glue if needed.

Kitchen Cabinets - Assembly Picture
STEP 15:

Here is a top view of the cabinet after the bottom panel is installed.

Kitchen Cabinets - Assembly Picture
STEP 16:

Locate the spinning tray holders.

Kitchen Cabinets - Assembly Picture
STEP 17:

Place the metal plate on top of the wooden plate as shown in the photo.

Kitchen Cabinets - Assembly Picture
STEP 18:

Note that the pre-drilled holes in the wooden plate should align with the holes in the metal plate.

Kitchen Cabinets - Assembly Picture
STEP 19:

Once you have aligned the plates, secure them with screws.

Kitchen Cabinets - Assembly Picture
STEP 20:

Place the bottom spinning tray on top of the plate.

Kitchen Cabinets - Assembly Picture
STEP 21:

While holding the spinning tray, check on the other side to see if the holes are aligned.

Kitchen Cabinets - Assembly Picture
STEP 22:

Secure the spinning tray to the plate using screws.

Kitchen Cabinets - Assembly Picture
STEP 23:

Locate the rear side panel and insert it into the grooves. Make sure the two pre-drilled holes at the top align with the face frame.


In the photo, you can see the holes, the face frame and the installer's hands.

Kitchen Cabinets - Assembly Picture
STEP 24:

Make sure the rear side panel is secured and aligned with all the grooves.

Kitchen Cabinets - Assembly Picture
STEP 25:

Staple the side panel to the rear side panel using 3/4'' staples every 4 to 6''.


Start from the top.

Kitchen Cabinets - Assembly Picture
STEP 26:

Staple down to the bottom.

Kitchen Cabinets - Assembly Picture
STEP 27:

Locate the upper spinning tray holder and connect it to the partition panel using four screws.

Kitchen Cabinets - Assembly Picture
STEP 28:

Here is a side view of the partition panel with the attached spinning tray holder.

Kitchen Cabinets - Assembly Picture
STEP 29:

Place the partition panel with the attached holder on to the upper spinning tray.

Kitchen Cabinets - Assembly Picture
STEP 30:

Make sure that the plate holes align with the pre-drilled holes in the upper spinning tray.

Kitchen Cabinets - Assembly Picture
STEP 31:

Once the holes are aligned, connect the upper spinning tray to the partition panel using four screws.

Kitchen Cabinets - Assembly Picture
STEP 32:

Here is a top view of the upper spinning tray after it has been secured to the partition holder.

Kitchen Cabinets - Assembly Picture
STEP 33:

Insert the upper spinning tray into the cabinet.

Kitchen Cabinets - Assembly Picture
STEP 34:

Make sure to place the partition panel on the pre-installed support panels.

Kitchen Cabinets - Assembly Picture
STEP 35:

Connect the partition panel to the support panels using two screws for each side.

Kitchen Cabinets - Assembly Picture
STEP 36:

onnect the partition panel to the support panels using two screws for each side (four total).

Kitchen Cabinets - Assembly Picture
STEP 37:

Locate the back panel and insert it into the grooves of the rear side panels as shown in the photo.

Kitchen Cabinets - Assembly Picture
STEP 38:

Make sure the back panel is align inside the grooves.

Kitchen Cabinets - Assembly Picture
STEP 39:

Locate the upper support panel.

Kitchen Cabinets - Assembly Picture
STEP 40:

Connect the upper support panel using two screws for each side.

Kitchen Cabinets - Assembly Picture
STEP 41:

Secure the back panel using screws in the pre-drilled holes.

Kitchen Cabinets - Assembly Picture
STEP 42:

Locate both parts of the toe kick and connect them using screws as shown in the photo.

Kitchen Cabinets - Assembly Picture
STEP 43:

Here is a view of the bottom of the cabinet to illustrate how the toe kick panels should be installed.

Kitchen Cabinets - Assembly Picture
STEP 44:

Connect the toe kick panels to the cabinet using 3/4'' staples every 4''.

Kitchen Cabinets - Assembly Picture
STEP 45:

Congratulations! Your cabinet is now ready.

Kitchen Cabinets - Assembly Picture
STEP 46:

Remember to install the doors only after the entire cabinet installation is complete in order to prevent damages.


Locate the parts needed for door installation.

Kitchen Cabinets - Assembly Picture
STEP 47:

Place both doors as shown in the photo.

Kitchen Cabinets - Assembly Picture
STEP 48:

Insert the hinges to connect both doors together and secure with screws.

Kitchen Cabinets - Assembly Picture

Wall Appliance Garage

STEP 1:

Locate the front face frame.

Kitchen Cabinets - Assembly Picture
STEP 2:

Locate the two top support pieces.

Kitchen Cabinets - Assembly Picture
STEP 3:

Insert the top support pieces into the pre-drilled holes in the front face frame.

Kitchen Cabinets - Assembly Picture
STEP 4:

Connect the top panel to the top support pieces using four screws in the pre-drilled holes on the top support pieces.

Kitchen Cabinets - Assembly Picture
STEP 5:

Close up on the way to connect the top panel to the top support pieces.

Kitchen Cabinets - Assembly Picture
STEP 6:

Connect the side panel to the front face frame using two brackets as shown in the photo.

Kitchen Cabinets - Assembly Picture
STEP 7:

Connect the other side panel to the front face frame using two additional brackets.

Kitchen Cabinets - Assembly Picture
STEP 8:

Connect the back side panel to the top panel using three screws in the pre-drilled holes.

Kitchen Cabinets - Assembly Picture
STEP 9:

We recommend reinforce the structure of the cabinet using 3/4'' staples as shown in the photo (to connect the back side panel to the front side panel). You may also use the supplied brackets instead of staples to complete this task.

Kitchen Cabinets - Assembly Picture
STEP 10:

Repeat the last two steps with the other back side panel.

Kitchen Cabinets - Assembly Picture
STEP 11:

Slide in the back panel and secure with four screws in the pre-drilled holes.

Kitchen Cabinets - Assembly Picture
STEP 12:

Slide in the door into the slots starting from the bottom to the top.

Kitchen Cabinets - Assembly Picture
STEP 13:

Flip the cabinet and make sure the doors opens and closes properly.

Kitchen Cabinets - Assembly Picture
STEP 14:

Your cabinet is now ready!

Kitchen Cabinets - Assembly Picture

Wall Cabinet

STEP 1:

Disconnect door from frame in order to prevent damages during assembly and installation.

Kitchen Cabinets - Assembly Picture
STEP 2:

Locate the side panels.

Insert side panel into the groove in the frame.

Kitchen Cabinets - Assembly Picture
STEP 3:

Secure the side to the frame by using a staple gun (3/4'' Deep by 1/4'' Wide staples are recommended).

Staple the side every 6''.

Kitchen Cabinets - Assembly Picture
STEP 4:

For increased durability use a glue gun (hot glue) to glue the joint of the frame and the side panels together.

Make sure to leave a thin, even layer and to wipe off the excess glue after it is dry.

Kitchen Cabinets - Assembly Picture
STEP 5:

Repeat Steps 3 and 4 with the other side panel.

Kitchen Cabinets - Assembly Picture
STEP 6:

Locate the identical top and bottom panels.

Insert each of them in the grooves of the side panel. Make sure the notch on the side of the panels faces the frame.

Kitchen Cabinets - Assembly Picture
STEP 7:

Do NOT staple the top and bottom panels from the inside. Staples and glue will be used from the outside (see next step).

Kitchen Cabinets - Assembly Picture
STEP 8:

After the panels are inserted in the grooves. Secure them using staples every 4-6''.

Repeat this step with the other panel.

Kitchen Cabinets - Assembly Picture
STEP 9:

Add a layer of hot glue. Repeat this step with the other panel.

Kitchen Cabinets - Assembly Picture
STEP 10:

Locate both shelves (left) and the back panel (right).

Kitchen Cabinets - Assembly Picture
STEP 11:

Slide the back panel in the grooves.

Kitchen Cabinets - Assembly Picture
STEP 12:

Make sure the back panel is inserted properly.

Kitchen Cabinets - Assembly Picture
STEP 13:

Locate the shelf holders (left) and the screws to the back (right).

Use four screws to secure the back panel to the frame (in each pre-drilled hole).

Kitchen Cabinets - Assembly Picture
STEP 14:

Using a regular Philips Head Screwdriver, secure all four screws.

Kitchen Cabinets - Assembly Picture
STEP 15:

Use two staples (either 3/4'' or 1'' staples) to secure the side of the cabinet.

Do not staple more than 1/2'' below the top or you will "miss" the back plywood piece.

Kitchen Cabinets - Assembly Picture
STEP 16:

Repeat this process with each side (four in total).

Congratulations! Your cabinet is now ready.

Remember to re-install the doors and shelves after installation in order to avoid damages.

Kitchen Cabinets - Assembly Picture